grabcad
Bent Spring
Bent Spring
bent spring 3D Models
5,053 resultsSponsored
grabcad
grabcad
Bent Spring
Bent Spring
grabcad
Bent Spring With Changing outer diameter
Catia Created spring that is bend 180 deg with diameter varying from start 20mm , 90 de...
grabcad
Round-hex-round bent varying spring
A spring bent 180 deg with an outer shape that changes from a 20mm dia circle to a 30mm...
prusaprinters
Belt Deflection Tester - Spring Edition
This is an updated Belt Deflection Tester, designed to be used with closed-end springs....
grabcad
Best Spiral Spring In Solidworks
Best Spiral Spring In Solidworks
SPONSORED
🗳️ Will Keiko Fujimori win 2026 Peruvian election?
Latin American politics on the blockchain. Trade your conviction.
cults3d
Belt tensionner with spring 8x35
Hi, this is a belt tensionner using 8x35mm compression spring. Don't tight the m5 sc...
thingiverse
Belt tensionner with spring 8x35
Hi, this is a belt tensionner using 8x35mm compression spring. Don't tight the m...
thingiverse
Spring-loaded Ultimaker short belt tensioner
Mooncactus design only had two holes for the stepper motor and two screws on the lug si...
thingiverse
Spring Thunder - 5xShell Holder for Belt
Shell caddy designed to hold five Spring Thunder shells. Use heat to bend the tongue in...
thingiverse
Polargraph - timing belt and spring load
My take on a polargraph shown on Aarhus Mini Maker Fair Oct. 2016. Featuring: 1) Spring...
youmagine
Spring-loaded Ultimaker short belt tensioner
Mooncactus design on thingiverse only had two holes for the stepper motor(should be fou...
cults3d
HPI Sprint 2 belt tensioner
to add tension in the rear belt. Very usefull when changing the pulley ratio. Fit on ...
thingiverse
Prism Z belt springy idler
This is a an idler for the Z axis belt of your Prism Reprap (design by by Buback) Its t...
thingiverse
Nerf full dart mag spring bend guide
A couple of people have requested a full dart version of this: https://www.thingiverse....
thingiverse
Spring-loaded NEMA 17 steppers / belt tensioner
This is an improvement to precisely set and keep a given belt tension by pulling the st...
thingiverse
W124 Coupe Seat belt retract spring holder
Intended as a replacement for part no A 124 868 19 14 May need sanding to fit wor...
cults3d
Anet A8 Sprung Loaded belt Adjuster
Hope this will be of use .
prusaprinters
Minimalist belt tensioner (replaces tensioning springs)
A simple little belt tensioner. This uses a zip tie for tensioning, and has no sharp ed...
thingiverse
BI v2.5 String to Belt Conversion
You can find the official BI V2.5 Belt Conversion Kit here. My kit was designed before ...
thingiverse
BI v2.5 String to Belt Conversion
Switching from string to belt. Instr...
cults3d
Minimalist belt tensioner (replaces tensioning springs)
A simple little belt tensioner. This uses a zip tie for tensioning, and has no sharp ed...
thingiverse
90 degree bend for wire/string
90 degree bend to Guide string or wire. works like a pulley
thingiverse
Anet A8 Sprung Loaded belt Adjuster
Hope this will be of use .
thingiverse
Minimalist belt tensioner (replaces tensioning springs)
A simple little belt tensioner. This uses a zip tie for tensioning, and has no sharp ed...
thingiverse
Axis x belt holder with spring cr 10
https://youtu.be/JiWlcMgOu_g x belt holder with spring.. very easy
thingiverse
Best Stiffer Shifter Mod Logitech Shifter Spacer Spring
||VERY IMPORTANT READ ALL INSTRUCTION|| Take about 3minute to print. This mod is ma...
thingiverse
Anet A8 X belt holder and spring tensioner
I started to rebuild one of my Anet A8 printers and first thing to come was X belt hold...
thingiverse
Anet E10/12 X Y belt Spring tensioner
Spring: like the Bedlevel Spring from Anet
thingiverse
Retractable string keychain belt and pants clip
This clip attaches to your belt or pants and holds anything cirucular like a retractabl...
Sponsored
Sponsored